How to Install TWRP 3.0.0 Recovery on Samsung Galaxy S7 Edge G935F

Good news for Samsung Galaxy S7 Edge users.There is a working unofficial TWRP 3.0.0 Recovery available for the devices.Developer jcadduono over at Xda has just posted official builds of TWRP 3.0.0 Recovery For Samsung Galaxy S7 Edge G935F.It is not an official release but is a working built.

Follow the step by step guide on How to Flash / Insatll TWRP 3.0.0 Recovery On Samsung Galaxy S7 Edge G935F.


÷ Features:

•MTP support
•USB Mass Storage support
•Micro SDcard and USB OTG storage support
•f2fs file system support (read, write, format, backup & restore)
•exFAT file system support (read, write, format, backup & restore)
•NTFS file system support (read, write, format)
•Backup & restore of modem/baseband/firmware (not bootloader!)
•ADB root
•Full SELinux support
•Built in android 6.0 tree.

View my Flipboard Magazine.


÷ Prerequisites:

•This only For Galaxy S7 Edge G935F.

•Battery must be more than 60%.

*Disclaimer:

Android Custom ROM fix ® provide various Firmware Updates and Rooting process along with Custom ROM,Modes,file are all belong  to their owners/developers. The autor of this site or the developers are not responsible,  if you damage or brick your device.Do it on your own risk and follow the instruction properly.

* Important:

Backup important files stored on your device before proceeding with the steps below, so that in case something goes wrong you’ll have backup of all your important files.

÷ How to Install TWRP 3.0.0 Recovery on Samsung Galaxy S7 Edge G935F:


Step 1 – Download TWRP 3.0.0 Recovery package for Samsung Galaxy S7 Edge and extract this file anywhere in your computer:


Step 2 – Download ODIN v3.09 which will help you to install CWM Recovery on Samsung Galaxy S7 Edge .

Step 3 – Switch OFF your phone. Now go toDownload Mode. How? Press and hold the Volume Down + Home buttons together, and then press the Power button till you see the construction Android robot and a triangle. Press Power again to confirm to enter intoDownload Mode.

Step 4 – Make sure you have your Samsung Galaxy S7 Edge USB drivers installed on your computer.


Step 5 – Open ODIN on your computer. Connect your phone to your computer while your phone is in the Download Mode.

Step 6 – If your phone is connectedsuccessfully, one of the ID:COM boxes will turn yellow with the COM port number. This step might take some time.

Step 7 – Now select the following file that you have to flash/install on your phone. This file will be found from the extracted file in Step 1.

Click on ‘PDA’ / ‘AP’ and select the package file (twrp-3.0.0-0-zerolteeu-zerolteeu.img.tar) you downloaded in step 1 for your phone.

Step 8 – In ODIN, check the Auto Reboot andF. Reset Time options, if not already.

Step 9 – Now click on the Start button in ODIN. Installation process will start and would take a few minutes to complete.

Step 10 – After the installation is completed, your phone will reboot into Recovery Mode automatically and install the root package / files. Your ID:COM box will also turn green.

Step 11 – After you see the home screen, unplug your phone from the computer.

That’s it! Your Samsung Galaxy S7 Edge has now been flashed with TWRP 3.0.0. To enterRecovery Mode, shut down phone and then hold down the Home + Volume Up buttons and press the Power button for about 5 seconds to enter Recovery Mode.

Like this post? PLZ Hit the share buttons below to share this article with your friends on Facebook, Google + and Twitter.

PLZ Follow Us On Flipboard 4 More Galaxy S7 latest updates.

PLZ Use the comment box below to contribute more ideas & Suggestions .

Best Regards.